
USB-C 插座,SMD 附外殼定位柱
表面貼裝觸點配四個通孔外殼支腳。外殼支腳承受插拔力,而非焊盤。
Specification on request
Every part on this page is a real part from our Shenzhen plant, photographed as it comes off the line. The range is built to drawing, so most parts have no catalogue rating to publish: send the drawing, the sample or the part number and we will confirm the specification for your part rather than quote a series figure that does not apply to it.
決定佈局的安裝方式下的插座與插頭:僅板裝、板裝加外殼定位柱、面板用螺絲耳,以及線纜端用屏蔽插頭。

表面貼裝觸點配四個通孔外殼支腳。外殼支腳承受插拔力,而非焊盤。
Specification on request

兩側各有帶安裝孔的平耳,適用於須以螺絲鎖固在面板或壓鑄外殼上的插座。
Specification on request

兩個插座堆疊於單一外殼中,配一個通孔引腳尾塊,適用於需要在同一面板開孔同時具備充電埠與資料埠的設備。
Specification on request

同一零件安裝於板上,外殼卡扣穿過 PCB 並焊接。這些卡扣承受插拔力;訊號焊盤僅傳輸訊號。
Specification on request

觸點模組上方覆蓋帶翼形卡扣的屏蔽片,適用於焊接後模壓包覆的線纜端。
Specification on request
子彈頭連接器、防電弧零件與電池組模組。已公布參數的系列有獨立頁面;其餘按圖面報價。

兩個大面積鍍層觸點加一個訊號針,附保護蓋。防電弧零件用於帶電連接電池組的場合。
Specification on request


長殼體,兩端各有一個安裝孔,配兩排刀片式觸點,適用於嵌入固定外殼的電池組。
Specification on request


當客戶希望整塊板由單一供應商供應,而非連接器廠與排針廠分開供應時,我們也會生產這些通用零件。

單排彎腳設計,使對插方向與 PCB 平行。帶防呆鍵殼體。
Specification on request

D-SUB 外殼內的兩個電源觸點。圖面規定 PCB 孔位配置:總長 31.19,安裝孔中心距 25,觸點中心距 6.86。
Specification on request
All of it, on one board
這是展示板,不是產品:板上的每個模組都出自我們之手,一次組裝成型,讓買家能在同一比例下檢視各連接埠,而不是看分散的個別照片。


Two USB-A blocks, two stacked blocks with an RJ45 pair above USB-C and Micro-USB. Ask for the port list you need and we will say which of them share a shell.
如果您需要的零件未列在這裡,這並非拒絕——而是模具問題。請寄送圖面或樣品,我們會告知這是既有殼體的變體,還是需要新開模具。