Battery packs
Battery pack connectors — power contacts and a signal grid in one housing
A pack connector is where the buyer stops choosing a plug and starts choosing a housing: the power contacts, the signal pins that tell the BMS what is happening, the keying that stops a reversed mate, and the flange or through-hole pattern that fixes it to the enclosure. We build these to drawing in our Shenzhen plant, in sealed versions with a gasket and in board-mount versions without one.
- High-current power contacts plus a signal grid in the same block
- Sealed version with a full perimeter gasket
- Board-mount version with through-hole pins
- Flange with corner fixing holes and keyed housing
- Produced in our Shenzhen plant

Specification
What the housing carries, and what is quoted per drawing
Contact count and housing style are visible from the part; current per contact, sealing class and pin assignment belong to the drawing for your pack. Those are quoted, not assumed.
| Power contacts | 2 or 5 large contacts |
|---|---|
| Signal contacts | Multi-pin grid in the centre of the block |
| Sealing | Gasket version available |
| Mounting | Flange with corner fixing holes, or through-hole board pins |
| Keying | Asymmetric housing so a reversed mate will not enter |
Why the signal pins live inside the power block
On a pack, voltage sense and temperature have to travel with the power, and a separate harness is the first thing that gets left unplugged. Putting the signal grid inside the same housing makes one mate do both jobs and makes a partial connection impossible to ignore.
The cost is a tighter design: the signal pins sit near the power contacts, so creepage and clearance have to be checked at the drawing stage rather than at the sample stage.
Sealed or board-mount
The sealed version carries a full perimeter gasket and is fixed through the flange, so the housing seals against the enclosure wall rather than the board. That is what an e-bike or a swap-station pack needs: the connector is part of the enclosure, not part of the electronics.
The board-mount version drops the gasket and solders to the board through pins and posts. It suits a pack that is already inside a sealed box, where the connector only has to be repeatable, not watertight.
Keying, and why buyers ask for it
A pack that can be inserted the wrong way round will eventually be inserted the wrong way round - by a dealer, by a rider, by a service technician. The asymmetric housing is the cheapest protection available, and it costs nothing extra at tooling time if it is in the first drawing.
If the same housing has to serve two pack variants, tell us at the drawing stage: the key can be changed per variant rather than moulding two bodies.
What to send for a quotation
The pack drawing with the contact positions, the current per power contact, the number and function of the signal pins, the sealing requirement, and whether the housing fixes to the enclosure or to the board. With those, the tooling question can be answered in the first reply.
Samples come from the plant that will run production, so what you approve is what ships.
FAQ
Questions buyers ask before ordering
- How many power contacts are there?
- It depends on the block: the versions we build carry 2 or 5 large power contacts, with a signal grid in the centre. Send the drawing and we will confirm the count for your part.
- Is it waterproof?
- A gasket version exists and seals against the enclosure through the flange. The sealing class is quoted per drawing - we will not state an IP figure we have not tested.
- Can the signal pins be assigned differently?
- Yes, pin assignment follows your drawing. The housing and the contact positions are fixed once the tool is made, so settle the assignment before tooling.
- Do you supply the mating half as well?
- Yes, the pair is built together. Ask for male and female as a set, or specify which half you need if the other side is already in your product.
- Samples come from the plant that will run production
- Non-standard tab spacing or barrel size is a tooling question, quoted separately
- We will not promise a sample date before the drawing is reviewed
Send the drawing or the part number
We quote against your specification rather than a catalogue number. Include the application, the annual volume and any test report the buyer requires.