Skip to content
Hengchang Technology

Connector range — photographed, not illustrated

Every part on this page is a real part from our Shenzhen plant, photographed as it comes off the line. The range is built to drawing, so most parts have no catalogue rating to publish: send the drawing, the sample or the part number and we will confirm the specification for your part rather than quote a series figure that does not apply to it.

USB Type-C

Receptacles and plugs in the mounting styles that decide the layout: board-only, board plus shell posts, screw ears for a panel, and shielded plugs for a cable end.

USB-C receptacle, SMD with shell posts

USB-C receptacle, SMD with shell posts

Surface-mount contacts with four through-hole shell legs. The shell legs carry the insertion load, not the solder pads.

Specification on request

USB-C receptacle with screw ears

USB-C receptacle with screw ears

Flat ears either side with a fixing hole, for a socket that has to be screwed to a panel or a die-cast housing.

Specification on request

USB-C, two ports in one shell

USB-C, two ports in one shell

Two receptacles stacked in a single shell with one through-hole tail block, for a device that needs a charging port and a data port at the same panel cut-out.

Specification on request

USB-C receptacle, soldered in place

USB-C receptacle, soldered in place

The same part on a board, with the shell tabs through the board and soldered. Those tabs take the insertion load; the signal pads only carry the signals.

Specification on request

USB-C plug, shielded

USB-C plug, shielded

Shield plate over the contact block with wing tabs, for a cable end that is soldered and overmoulded.

Specification on request

Battery and power

Bullet connectors, anti-spark parts and pack blocks. The series with published figures have their own pages; the rest are quoted against the drawing.

AS150 anti-spark connector

AS150 anti-spark connector

Two large plated contacts plus a signal pin, with a protective cap. The anti-spark part is used where a pack is connected live.

Specification on request

XT90-S on a finished lead

XT90-S on a finished lead

The connector arrives soldered, heat-shrunk and polarity-labelled, so the assembly step does not have to happen on your line.

Specifications for this series
Blade battery connector, strip form

Blade battery connector, strip form

Long body with a fixing hole at each end and two rows of blade contacts, for a pack that seats against a fixed housing.

Specification on request

Sealed pack connector, 5 power contacts

Sealed pack connector, 5 power contacts

Full perimeter gasket, five large contacts and a signal grid in one block, fixed through the flange instead of the board.

Specifications for this series
Board-mount pack connector, 2 power contacts

Board-mount pack connector, 2 power contacts

Flanged housing with through-hole pins and posts, for a pack that is already inside a sealed enclosure.

Specifications for this series

Board level

The commodity parts we also run when a customer wants one supplier for the whole board rather than a connector house and a header house.

Pin header, 5 positions, right angle

Pin header, 5 positions, right angle

Single row with bent legs so the mating direction is parallel to the board. Keyed body.

Specification on request

D-SUB 2P, female, board mount

D-SUB 2P, female, board mount

Two power contacts in a D-SUB shell. Drawing gives the PCB hole pattern: 31.19 overall, 25 between the fixing holes, 6.86 between the contacts.

Specification on request

All of it, on one board

The ports, assembled side by side

This is a demo board, not a product: every block on it is one of ours, assembled in one shot so a buyer can see the ports at the same scale instead of as separate photographs.

Demo board, front view, carrying USB-A, RJ45, USB-C and Micro-USB port blocks
The same demo board seen at an angle, showing the height difference between the port blocks

Two USB-A blocks, two stacked blocks with an RJ45 pair above USB-C and Micro-USB. Ask for the port list you need and we will say which of them share a shell.

Send the drawing or the part number

If the part you need is not shown here, that is not a refusal - it is a tooling question. Send the drawing or the sample and we will say whether it is a variant of an existing body or a new tool.